Skip to main content

Full text of "Paper Crafts"

See other formats


Frankenstein! A Papier-MActchA© Project 



.1 



Make Projects 



build, hack, tweak, share, discover. 



Frankenstein! A Papier-Mache 

Project 



Written By: charcol!98 



TOOLS: 



Drill with screwdriver bits (1) 
Gloves - both safety and latex (1) 
Jigsaw (1) 

Scissors or paper cutter (1) 
Shallow pan (1) 
Small paint brushes (1) 
Wide sponge paint brushes (1) 
Wire cutters/pliers (1) 



O PARTS: 

Approximately 10 rolls of 1.5-inch 
masking tape (1) 

8-oz. bottles of Elmer's White Glue (8) 

1 roll gray duct tape (1) 

2.5" wood screws (15 to 18) 

• Plywood (2 sheets) 
Scrap wood for spacers (1) 
Black acrylic paint (8 oz.) 
Green acrylic paint (4 oz.) 

Misc. acrylic paint for shading and detail 

Newspapers or magazines with 
newsprint paper (1) 

• Hex wire (1) 



© Make Projects 



www.makeprojects.com 



Page 1 of 7 



Frankenstein! A Papier-MActchA© Project 
SUMMARY 

Papier-mache has been around for many years. I will be using one of the easiest ways to 
make it, although not the cheapest. Papier-mache is basically cutting strips of paper, 
saturating them in a mixture of glue and water and layering them across a pre-shaped form 
to dry. After drying, it may be painted. 

Many of these items you can find around your home or substitute to make the project less 
expensive. 



Step 1 — Frankenstein! A Papier-Mache Project 




• Lay two pieces of plywood flat. If you can, freehand-draw the body on the first piece of 
plywood. Cut out using a jig-saw. I laid on the wood and roughly traced around my body. 
Make this fun; you only need a guide. 

• Using the first cut-out as a pattern, trace and cut a second body piece. 

• On scrap wood trace 4 shoe patterns. Cut out. 



© Make Projects 



www.makeprojects.com 



Page 2 of 7 



Frankenstein! A Papier-MActchA© Project 



Step 2 




• Place scrap wood on one of the body pieces to form a two-inch rise. 

• Position the second board on top. Using a drill, screw through all layers avoiding screwing 
completely through the back of the bottom board. 

• Place scrap wood on bottom edge of legs to allow "shoes" to be attached. Now is the time 
to adjust bottom of shoes to balance Frankenstein. 

Step 3 




• Begin wrapping newsprint around form. Use more newsprint where body parts need bulk. 
Use masking tape to hold paper in place 

• For chest and shoulder area, form hex wire around form and stuff with additional paper. 
Wrap wire with newsprint and secure with masking tape. 

• Wrap legs with sheets of newspaper and tightly secure with masking tape. You will now 
begin the task of covering from the neck to the feet with strips of masking tape. Run the 
tape in different directions, carefully covering every inch of newsprint. 



© Make Projects 



www.makeprojects.com 



Page 3 of 7 



Frankenstein! A Papier-MActchA© Project 



Step 4 




A 



• PLEASE USE CAUTION WHEN WORKING WITH WIRE. USE GLOVES AND 
OTHER SAFETY PRECAUTIONS. 

• Form arms from hex wire. 

• Cover with newsprint and masking tape. 

• Leave ends out and cut with wire cutters to form ends to attach arms to body. 

• Insert wire from arm into wire at shoulder. Using pliers or wire cutters pull through one of 
the hex openings and twist to tighten. Turn down any sharp edges. 



Step 5 




• For feet, form boxy feet and stuff with paper. Hex wire needs to go under feet as well. 

• Cover with duct tape and then with masking tape to make this area stronger since this part 
is more prone to being stepped on or bumped. 



© Make Projects 



www.makeprojects.com 



Page 4 of 7 



Frankenstein! A Papier-MActchA© Project 



Step 6 




• Cut newsprint into 1 .5-inch-wide strips. Cut each strip into manageable lengths. If you like, 
now is a great time to get the gloves out! This is the messy part. 

• In a medium shallow bowl, mix 2 parts school glue (Elmer's Glue is best) to 1 part water. 
Mix well. Mixture should be creamy in consistency, not watery. 

• Lay a strip of newsprint across mixture, allowing one side to become damp with glue. 
Raise strip up with one hand and while holding, pull strip through two fingers as if forming 
scissors, thus removing excess glue from strip. Repeat to coat other side. Immediately 
place strip on form, smoothing as you go. 

• Repeat process overlapping next strip by 1/8 inch-1/4 inch until all form is covered. 

• Paper should not be soggy! If drips appear, gently rub off and try to remove more glue 
before placing strips on form. 



© Make Projects 



www.makeprojects.com 



Page 5 of 7 



Frankenstein! A Papier-MActchA© Project 



Step 7 






• Cut one of the two head forms off. This will allow for the papier-mache to be set back 
some and still have a sturdy base. 

• Make Frankenstein's head. Do not be intimidated by this. Remember that Frankenstein 
himself was far from perfect! This can be as realistic or folk-art as you want it to be. 

• Layer many pieces of newspaper/magazines into a square or oval shape securing tightly 
with masking tape. Roll pieces up for eyebrow bones and lips and cheek bones. For a 
nose, tear off paper and crumple into a triangle, pushing and forming into shape of a nose. 
Add pieces of paper where needed to add shape, holding together with masking tape. Lay 
pieces out on head, taping them down. Continue to tape the remainder of head. Using 
blank newsprint, papier-mache face. Let dry. Sketch on facial features. 

• Place this head on the wooden part of the Frankenstein head. Using a drill, screw a couple 
of screws into the wood, catching the back of the papier-mache head. Cover wood with 
newsprint and masking tape extending around to front of head. Papier-mache back of 
head, feathering into front of head to form one complete head. By making this a two-part 
head, there will not be the possibility of a broken neck later. At this time, "bolts" may be 
added if desired. They are simply rolled newsprint that has been papier-mached and taped 
to side of neck area. 



© Make Projects 



www.makeprojects.com 



Page 6 of 7 



Frankenstein! A Papier-MActchA© Project 



Step 8 




• I chose to use gloves for hands. Stuff gloves with fiberfill and insert wire into fingers to 
allow fingers to be bent. Use wire to thread up into sleeve and tie to hex wire. 

• Paint body black with gray/white lapels and mock turtleneck. Shadow body around bends 
in arms, around knees and to divide pants and shoes. Also shadow around bottom of 
jacket. 

• Finish painting face and hair. Shadow and highlight where needed. Finish off by adding a 
little flower for Frankie to wear. 

• If you are going to use this outdoors, please understand that it must be finished with an 
outdoor varnish. Also, it is best kept protected from the elements. 

This document was last generated on 2012-11-03 01:39:05 AM. 



© Make Projects 



www.makeprojects.com 



Page 7 of 7